manualshive.com logo in svg

HP G2 Series, Installation Manual

Share
Download
HP G2 Series Installation Manual Download Page 69

Heavy Duty Stabilizer kit

Kit overview

The Heavy Duty Stabilizer kit provides stability and support and prevents possible tipping when you install, remove, or access
equipment within the HPE Advanced G2 Series or HPE Enterprise G2 Series racks.

Use the heavy duty stabilizer kit if you have a stand-alone rack with a single rack-mountable component that exceeds 99.8 kg
(220 lb) or if you have three or fewer bayed racks with a single rack-mountable component that exceeds 99.8 kg (220 lb).

NOTE: This kit is only available for 600mm wide racks.

Kit contents (BW961A)

Item

Quantity

Heavy duty front stabilizer mount

1

Heavy duty stabilizer feet

2

M8 x 16-mm bolt

8

M8 x 30-mm bolt

2

M8 flat washer

10

Required tools

The following tools are required for installation:

• Ratchet with sockets

• Adjustable wrench

Installing the heavy duty stabilizer

Procedure

1. Install the front stabilizer mount.

a. Align the front stabilizer mount to the mounting holes on the rack front caster plate.

b. Insert and partially tighten four M8 x16-mm bolts with washers, securing the front stabilizer mount to the front caster

plate.

Heavy Duty Stabilizer kit

69

Summary of Contents for G2 Series















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands