manualshive.com logo in svg

HP G2 Series, Installation Manual

Share
Download
HP G2 Series Installation Manual Download Page 39

Reference

Item

1

Rack grounding lug

2

M8 Belleville toothed washer

3

M8 flat washer

4

M8 hex nut

The rack grounding lug can be moved to any position on the top or bottom of the rack.

Installing the ground bonding kit on side panels

Procedure

1. Connect a 36.83-cm (14.5-inch) and a 15.24-cm (6-inch) grounding strap with connectors together.

2. Insert a T-25 Torx screw through the end of the 36.83-cm (14.5-inch) grounding strap and secure the screw to the middle

system chassis rail.

3. Place the end of the 15.24-cm (6-inch) grounding strap over the grounding lug on the bottom side panel.

4. Place an M8 internal serrated lock washer and an M8 hex nut over the grounding lug on the bottom side panel and tighten

the washer.

5. Repeat steps 1 through 4 for the other bottom side panel.

IMPORTANT: The location of the welding stud on your model may vary.

Installing the ground bonding kit to the top side panel

Procedure

1. Connect a 36.83-cm (14.5-inch) and a 15.24-cm (6-inch) grounding strap with connectors together.

2. Insert a T-25 Torx screw through the end of a 36.83-cm (14.5-inch) grounding strap, and then secure the screw to the

middle system chassis rail.

Ground Bonding kit

39

Summary of Contents for G2 Series















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands