manualshive.com logo in svg

HP G2 Series, Installation Manual

Share
Download
HP G2 Series Installation Manual Download Page 10

Rack option kit

Part number

Description

Stabilizer kit

BW932A (600mm)

– or –

BW933A (800mm)

Anti-tip stabilizer kits provide stability and support
when equipment is installed, removed, or accessed
within the rack. Heavy-duty stabilizer kits should be
used when a single racked component exceeds
200lbs.

Stabilizer kit, heavy duty

BW961A (600mm)

Anti-tip stabilizer kits provide stability and support
when equipment is installed, removed, or accessed
within the rack. Heavy-duty stabilizer kits should be
used when a single racked component exceeds
200lbs.

This kit is only available for 600mm wide racks.

Tie Down Kit

Q9V01A

This kit is used to secure the rack to the data center
floor.

HPE Rack baying kit options

Not all baying kits fit with all racks. Use the image below to determine which baying kit to use based on how the racks are set
up in your data center.

Rack options

10

Summary of Contents for G2 Series















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands