manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 32

24 

If you do not specify an interface type, this command clears statistics for all interfaces. 

If you specify only the interface type, this command clears statistics for all interfaces of that type. 

If you specify both the interface type and the interface number, this command clears statistics for the 
specified interface. 

Examples 

# Clear the statistics of GigabitEthernet 1/0/1. 

<Sysname> reset counters interface gigabitethernet 1/0/1 

Related commands 

•

 display 

interface

 

•

 

display counters interface

 

•

 

display counters rate interface

 

reset ethernet statistics 

Use 

reset ethernet statistics

 to clear the Ethernet module statistics.  

Syntax 

reset ethernet statistics slot slot-number

 

Views 

User view 

Predefined user roles 

network-admin 

network-operator 

Parameters 

slot slot-number: 

Clears the Ethernet module statistics on the specified IRF member device. The 

slot-number

 argument represents the ID of the IRF member device.  

Examples 

# Clear the Ethernet module statistics on IRF member 6.  

<Sysname> reset ethernet statistics slot 6 

reset packet-drop interface 

Use 

reset packet-drop interface

 to clear the dropped packet statistics on an interface or multiple 

interfaces.  

Syntax 

reset packet-drop interface 

[ 

interface-type 

[ 

interface-number 

] ] 

Views 

User view 

Predefined user roles 

network-admin 

Parameters 

interface-type

: Specifies an interface type. If you do not specify an interface type, this command 

clears dropped packet statistics on all the interfaces on the device.  

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands