manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 27

19 

Predefined user roles 

network-admin 

Usage guidelines 

With the 

flow-control receive enable

 command configured, an interface can receive, but not send, 

flow control frames. When the interface receives a flow control frame from its peer, it suspends 
sending packets to the peer. When traffic congestion occurs on the interface, it cannot send flow 
control frames to the peer. 

To handle unidirectional traffic congestion on a link, configure the 

flow-control receive enable

 

command at one end, and the 

flow-control

 command at the other. To enable both ends of the link to 

handle traffic congestion, configure the 

flow-control

 command at both ends. 

Examples 

# Enable Rx mode generic flow control on GigabitEthernet 1/0/1. 

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] flow-control receive enable 

Related commands 

flow-control 

flow-interval 

Use 

flow-interval 

to set the interface statistics polling interval. 

Use 

undo flow-interval 

to restore the default interval. 

Syntax 

flow-interval interval 

undo flow-interval 

Default 

The interface statistics polling interval is 300 seconds. 

Views 

Ethernet interface view 

Predefined user roles 

network-admin 

Parameters 

interval

: Sets the statistics polling interval, in seconds. The interval is in the range of 5 to 300 and 

must be a multiple of 5. 

Examples 

# Set the statistics polling interval to 100 seconds on GigabitEthernet 1/0/1. 

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] flow-interval 100 

interface 

Use 

interface 

to enter interface view. 

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands