manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 250

 

242 

Table 54 Command output 

Field Description 

Interface Interface 

name. 

GigabitEthernet1/0/1 QinQ-enabled interface. 

 

Related commands 

qinq enable

 

qinq enable 

Use 

qinq enable

 to enable QinQ on an Ethernet interface. 

Use 

undo qinq enable

 to restore the default. 

Syntax 

qinq enable

 

undo qinq enable

 

Default 

QinQ is disabled on Ethernet interfaces. 

Views 

Layer 2 Ethernet interface view, Layer 2 aggregate interface view 

Predefined user roles 

network-admin 

Examples 

# Enable QinQ on GigabitEthernet 1/0/1. 

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] qinq enable 

Related commands 

display qinq 

qinq ethernet-type

 

customer-tag 

Use 

qinq ethernet-type customer-tag

 to configure the CVLAN TPID. 

Use 

undo qinq ethernet-type customer-tag

 to restore the default CVLAN TPID. 

Syntax 

qinq ethernet-type

 

customer-tag

 

hex-value

 

undo qinq ethernet-type customer-tag 

Default 

The CVLAN TPID is 0x8100. 

Views 

System view 

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands