manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 247

 

239 

Examples 

# Enable MVRP globally. 

<Sysname> system-view 

[Sysname] mvrp global enable 

Related commands 

display mvrp running-status

 

mvrp gvrp-compliance enable 

Use 

mvrp gvrp-compliance enable

 to enable GVRP compatibility. 

Use 

undo mvrp gvrp-compliance enable

 to restore the default. 

Syntax 

mvrp gvrp-compliance enable 

undo mvrp gvrp-compliance enable 

Default 

GVRP compatibility is disabled. 

Views 

System view 

Predefined user roles 

network-admin 

Usage guidelines 

When you enable GVRP compatibility, the device can receive and send both MVRP and GVRP 
frames. 

Examples 

# Enable GVRP compatibility. 

<Sysname> system-view 

[Sysname] mvrp gvrp-compliance enable 

Related commands 

display mvrp running-status

 

mvrp registration 

Use 

mvrp

 

registration

 to set the MVRP registration mode on a port. 

Use 

undo mvrp

 

registration

 to restore the default. 

Syntax 

mvrp

 

registration

 { 

fixed

 | 

forbidden

 | 

normal

 } 

undo mvrp

 

registration 

Default 

The MVRP registration mode is normal. 

Views 

Layer 2 Ethernet interface view, Layer 2 aggregate interface view 

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands