manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 246

 

238 

Use 

undo mvrp enable

 to restore the default. 

Syntax 

mvrp enable

 

undo mvrp enable 

Default 

MVRP is disabled on a port. 

Views 

Layer 2 Ethernet interface view, Layer 2 aggregate interface view 

Predefined user roles 

network-admin 

Usage guidelines 

For MVRP to take effect on a port, make sure the following requirements are met: 

•

 

MVRP is enabled both globally and on the port. 

•

 

The port is in up state. 

•

 

The link type of the port is trunk. 

•

 

The port is not a member of an aggregation group. 

Examples 

# Enable MVRP on GigabitEthernet 1/0/1. 

<Sysname> system-view 

[Sysname] mvrp global enable 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] port link-type trunk 

[Sysname-GigabitEthernet1/0/1] mvrp enable 

Related commands 

display mvrp running-status

 

mvrp global enable 

Use 

mvrp global enable

 to enable MVRP globally. 

Use 

undo mvrp global enable

 to restore the default. 

Syntax 

mvrp global enable

 

undo mvrp global enable 

Default 

MVRP is disabled globally. 

Views 

System view 

Predefined user roles 

network-admin 

Usage guidelines 

To make MVRP take effect on a port, enable MVRP both on the port and globally. 

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands