manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 232

 

224 

Field Description 

Voice VLAN enabled ports and their modes

 

Voice VLAN-enabled port and its voice VLAN assignment 
mode. 

Port 

Name of the voice VLAN-enabled port. 

VLAN 

ID of the voice VLAN enabled on the port.  

Mode 

Voice VLAN assignment mode of the port: 

•

 Manual. 

•

 Automatic. 

 

Related commands 

voice-vlan aging 

voice-vlan enable 

voice-vlan mode auto 

voice-vlan security enable 

voice-vlan aging 

Use 

voice-vlan aging

 to set the voice VLAN aging timer. 

Use 

undo voice-vlan aging

 to restore the default. 

Syntax 

voice-vlan aging

 

minutes 

undo voice-vlan aging 

Default 

The voice VLAN aging timer is 1440 minutes. 

Views 

System view 

Predefined user roles 

network-admin 

Parameters 

minutes

: Sets the voice VLAN aging timer in the range of 5 to 43200 minutes. 

Usage guidelines 

In automatic voice VLAN assignment mode, the system starts an aging timer for a voice VLAN when 
assigning the port to the voice VLAN. If no voice packets are received on the port before the timer 
expires, the system removes the port from the voice VLAN.  

Set the voice VLAN aging timer only in automatic voice VLAN assignment mode. 

Examples 

# Set the voice VLAN aging timer to 100 minutes. 

<Sysname> system-view 

[Sysname] voice-vlan aging 100 

Related commands 

display voice-vlan state 

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands