manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 195

 

187 

•

 

If the MAC address does not match any MAC-to-VLAN entries or matches only a MAC-to-VLAN 
entry whose mask is not all Fs, the device does not dynamically learn the MAC address or 
assign the receiving port to the VLAN. 

Examples 

# Enable dynamic MAC-based VLAN assignment on GigabitEthernet 1/0/1. 

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] mac-vlan trigger enable 

Related commands 

port pvid forbidden 

port pvid forbidden 

Use 

port pvid forbidden

 to disable a port from forwarding packets that fail the exact MAC address 

match in its PVID. 

Use 

undo port pvid forbidden

 to restore the default. 

Syntax 

port pvid forbidden 

undo port pvid forbidden 

Default 

When a port receives packets whose source MAC addresses fail the exact MAC address match, the 
port forwards them in its PVID.  

Views 

Layer 2 Ethernet interface view 

Predefined user roles 

network-admin 

Usage guidelines 

Use this feature only with dynamic MAC-based VLAN assignment. 

Examples 

# Disable GigabitEthernet 1/0/1 from forwarding packets that fail the exact MAC address match in its 
PVID.  

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] port pvid forbidden 

Related commands 

mac-vlan trigger enable 

vlan precedence 

Use 

vlan precedence

 to set the VLAN matching order when both the MAC-based VLAN and IP 

subnet-based VLAN are configured on a port. 

Use 

undo vlan precedence

 to restore the default. 

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands