HP FlexNetwork 5130 HI series Command Reference Manual Download Page 187

Page: 187 / 306

179

Usage guidelines

You can configure a nonexistent VLAN as the PVID of a hybrid port. When you delete the PVID of a
hybrid port by using the

undo vlan

command, the PVID setting of the port does not change.

For correct packet transmission, configure the same PVID for a local hybrid port and its peer.

To enable a hybrid port to transmit packets from its PVID, you must assign the hybrid port to the PVID
by using the

port hybrid vlan

command.

•

The configuration made in Layer 2 Ethernet interface view applies only to the port.

•

The configuration made in Layer 2 aggregate interface view applies to the aggregate interface
and its aggregation member ports.

{

If the system fails to apply the configuration to the aggregate interface, it stops applying the
configuration to aggregation member ports.

{

If the system fails to apply the configuration to an aggregation member port, it skips the port
and moves to the next member port.

Examples

# Configure VLAN 100 as the PVID of the hybrid port GigabitEthernet 1/0/1, and assign
GigabitEthernet 1/0/1 to VLAN 100 as an untagged member.

<Sysname> system-view

[Sysname] vlan 100

[Sysname-vlan100] quit

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] port link-type hybrid

[Sysname-GigabitEthernet1/0/1] port hybrid pvid vlan 100

[Sysname-GigabitEthernet1/0/1] port hybrid vlan 100 untagged

Related commands

•

port

hybrid

vlan

•

port

link-type

port hybrid vlan

Use

port hybrid vlan

to assign a hybrid port to the specified VLANs.

Use

undo port hybrid vlan

to remove a hybrid port from the specified VLANs.

Syntax

port hybrid

vlan

vlan-id-list

{

tagged

untagged

}

undo port hybrid vlan

vlan-id-list

Default

A hybrid port is an untagged member of the VLAN to which the port belongs when its link type is

access

Views

Layer 2 Ethernet interface view, Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

vlan-id-list

: Specifies a space-separated list of up to 10 VLAN items. Each item specifies a VLAN ID

or a range of VLAN IDs in the form of

vlan-id1

vlan-id2

. The value range for VLAN IDs is 1 to 4094.

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Brands by name

Popular brands

HP FlexNetwork 5130 HI series, Command Reference Manual

Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Brands by name

Popular brands