manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 181

 

173 

Related commands 

display interface vlan-interface

 

name 

Use 

name 

to configure a name for a VLAN. 

Use 

undo name 

to restore the default. 

Syntax 

name text 

undo name 

Default 

The name of a VLAN is 

VLAN

 

vlan-id. 

The 

vlan-id

 argument specifies the VLAN ID in a four-digit 

format. If the VLAN ID has fewer than four digits, leading zeros are added. For example, the name of 
VLAN 100 is 

VLAN 0100

.  

Views 

VLAN view 

Predefined user roles 

network-admin 

Parameters 

text

: Specifies a VLAN name, a string of 1 to 32 characters. The string can include case-sensitive 

letters, digits, special symbols (see 

Table 35

), spaces, and other Unicode characters and symbols. 

Usage guidelines 

You can configure VLAN names for VLAN identification. When 802.1X or MAC authentication is 
configured on a device, you can specify VLANs by name on the RADIUS server for authorization 
VLAN assignment. 

Examples 

# Configure the name of VLAN 2 as 

test vlan

. 

<Sysname> system-view 

[Sysname] vlan 2 

[Sysname-vlan2] name test vlan 

Related commands 

display vlan 

service 

Use 

service 

to specify an IRF member device for forwarding the traffic on the current VLAN 

interface. 

Use 

undo service

 to restore the default. 

Syntax 

service slot

 

slot-number

 

undo service slot 

Default 

No IRF member devices are specified for forwarding the traffic on the VLAN interface. 

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands