manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 162

 

154 

Parameters 

vlan vlan-id-list

: Specifies a space-separated list of up to 10 VLAN items. Each item specifies a 

VLAN or a range of VLANs in the form of 

vlan-id1 

[ 

to

 

vlan-id2

 ]. The value for 

vlan-id2 

must be equal 

to or greater than the value for 

vlan-id1

. The value range for the 

vlan-id

 argument is 1 to 4094. If you 

set the STP, RSTP, or MSTP hello time, do not specify this option. 

time

: Sets the hello time in centiseconds, in the range of 100 to 1000 in increments of 100 (as in 100, 

200, 300). 

Usage guidelines 

Hello time is the time interval at which spanning tree devices send configuration BPDUs to maintain 
the spanning tree. If a device fails to receive configuration BPDUs within the set period of time, a new 
spanning tree calculation process is triggered. 

As a best practice, do not set the hello time with this command. Instead, you can specify the network 
diameter of the switched network by using the 

stp bridge-diameter

 command. This command 

makes the spanning tree protocols automatically calculate the optimal settings for the hello timer. If 
the network diameter uses the default value, the hello timer also uses the default value. 

Examples 

# In MSTP mode, set the hello time to 400 centiseconds.  

<Sysname> system-view 

[Sysname] stp timer hello 400 

# In PVST mode, set the hello time for VLAN 2 to 400 centiseconds.  

<Sysname> system-view 

[Sysname] stp vlan 2 timer hello 400 

Related commands 

•

 stp 

bridge-diameter 

•

 

stp timer forward-delay 

•

 

stp timer max-age 

stp timer max-age 

Use 

stp timer max-age

 to set the max age timer of the device.  

Use 

undo stp timer max-age

 to restore the default.  

Syntax 

stp

 [ 

vlan

 

vlan-id-list

 ] 

timer max-age

 

time

 

undo stp

 [ 

vlan

 

vlan-id-list

 ] 

timer max-age

 

Default 

The max age is 2000 centiseconds.  

Views 

System view 

Predefined user roles 

network-admin 

Parameters 

vlan vlan-id-list

: Specifies a space-separated list of up to 10 VLAN items. Each item specifies a 

VLAN or a range of VLANs in the form of 

vlan-id1 

[ 

to

 

vlan-id2

 ]. The value for 

vlan-id2 

must be equal 

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands