manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 158

 

150 

When the setting is configured on a member port in an aggregation group, it takes effect only after 
the port leaves the aggregation group.  

Examples 

# Enable root guard for GigabitEthernet 1/0/1.  

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] stp root-protection 

Related commands 

•

 stp 

edged-port 

•

 stp 

loop-protection 

stp tc-protection 

Use 

stp tc-protection

 to enable TC-BPDU attack guard for the device.  

Use 

undo

 

stp tc-protection

 to disable TC-BPDU attack guard for the device.  

Syntax 

stp tc-protection

 

undo stp

 

tc-protection

 

Default 

TC-BPDU attack guard is enabled. 

Views 

System view 

Predefined user roles 

network-admin 

Usage guidelines 

With TC-BPDU guard, you can set the maximum number of immediate forwarding address entry 
flushes that the device can perform every 10 seconds. For TC-BPDUs received that exceed the limit, 
the device performs a forwarding address entry flush when the interval elapses. This prevents 
frequent flushing of forwarding address entries. 

Examples 

# Disable TC-BPDU attack guard for the device. 

<Sysname> system-view 

[Sysname] undo stp tc-protection 

Related commands 

stp tc-protection threshold

 

stp tc-protection threshold 

Use 

stp tc-protection threshold

 to configure the maximum number of forwarding address entry 

flushes that the device can perform every 10 seconds. 

Use 

undo stp tc-protection threshold

 to restore the default.  

Syntax 

stp tc-protection threshold number 

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands