manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 144

 

136 

When the setting is configured in Layer 2 aggregate interface view, it takes effect only on the 
aggregate interface.  

When the setting is configured on a member port in an aggregation group, it takes effect only after 
the port leaves the aggregation group.  

Examples 

# In MSTP mode, disable the spanning tree feature on port GigabitEthernet 1/0/1.  

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] undo stp enable 

Related commands 

•

 

stp global enable 

•

 stp 

mode 

•

 

stp vlan enable 

stp global config-digest-snooping 

Use 

stp global

 

config-digest-snooping

 to enable Digest Snooping globally. 

Use 

undo

 

stp global config-digest-snooping

 to disable Digest Snooping globally. 

Syntax 

stp global config-digest-snooping 

undo stp global config-digest-snooping 

Default 

Digest Snooping is disabled globally. 

Views 

System view 

Predefined user roles 

network-admin 

Usage guidelines 

Enable this feature both globally and on ports connected to other vendors' devices. To minimize 
impact, enable the feature on all associated ports before you enable it globally. 

Examples 

# Enable Digest Snooping on GigabitEthernet 1/0/1 and then globally. 

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] stp config-digest-snooping 

[Sysname-GigabitEthernet1/0/1] quit 

[Sysname] stp global config-digest-snooping 

Related commands 

•

 display 

stp 

•

 stp 

config-digest-snooping 

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands