manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 143

 

135 

a temporary loop. You can enable the port to transit to the forwarding state rapidly by configuring it as 
an edge port. As a best practice, configure ports that directly connect to user terminals as edge ports.  

Typically, configuration BPDUs from other devices cannot reach an edge port, because the edge port 
does not connect to any other device. When BPDU guard is disabled, a port configured as an edge 
port functions as a non-edge port if it receives configuration BPDUs.  

On a port, the loop guard function and the edge port setting are mutually exclusive. 

When the setting is configured in Layer 2 Ethernet interface view, it takes effect only on that 
interface.  

When the setting is configured in Layer 2 aggregate interface view, it takes effect only on the 
aggregate interface.  

When the setting is configured on a member port in an aggregation group, it takes effect only after 
the port leaves the aggregation group.  

Examples 

# Configure GigabitEthernet 1/0/1 as an edge port. 

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] stp edged-port 

Related commands 

•

 stp 

bpdu-protection 

•

 stp 

loop-protection 

•

 stp 

root-protection 

stp enable 

Use 

stp enable

 to enable the spanning tree feature.  

Use 

undo stp enable

 to disable the spanning tree feature.  

Syntax 

stp

 

enable 

undo stp enable

 

Default 

The spanning tree feature is enabled on all ports. 

Views 

Layer 2 Ethernet interface view, Layer 2 aggregate interface view 

Predefined user roles 

network-admin 

Usage guidelines 

When you enable the spanning tree feature, the device operates in STP, RSTP, PVST, or MSTP 
mode, depending on the spanning tree mode setting. 

When you enable the spanning tree feature, the device dynamically maintains the spanning tree 
status of VLANs, based on received configuration BPDUs.  

When you disable the spanning tree feature, the device stops maintaining the spanning tree status. 

When the setting is configured in Layer 2 Ethernet interface view, it takes effect only on that 
interface.  

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands