manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 142

 

134 

Usage guidelines 

Path cost is an important factor in spanning tree calculation. Setting different path costs for a port in 
MSTIs allows VLAN traffic flows to be forwarded along different physical links. This results in 
VLAN-based load balancing. 

The path cost setting of a port can affect the role selection of the port. When the path cost of a port is 
changed, the system calculates the role of the port and initiates a state transition. 

When the setting is configured in Layer 2 Ethernet interface view, it takes effect only on that 
interface.  

When the setting is configured in Layer 2 aggregate interface view, it takes effect only on the 
aggregate interface.  

When the setting is configured on a member port in an aggregation group, is takes effect only after 
the port leaves the aggregation group.  

If you do not specify an MSTI or VLAN, this command sets the path cost of the ports in the MSTP 
CIST or in the STP or RSTP spanning tree. 

Examples 

# In MSTP mode, set the path cost of port GigabitEthernet 1/0/3 in MSTI 2 to 200.  

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/3 

[Sysname-GigabitEthernet1/0/3] stp instance 2 cost 200 

# In PVST mode, set the path cost of port GigabitEthernet 1/0/3 in VLAN 2 to 200.  

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/3 

[Sysname-GigabitEthernet1/0/3] stp vlan 2 cost 200 

Related commands 

•

 display 

stp 

•

 stp 

pathcost-standard 

stp edged-port 

Use 

stp edged-port

 to configure a port as an edge port.  

Use 

undo stp edged-port

 to configure a port as a non-edge port. 

Syntax 

stp edged-port 

undo stp edged-port 

Default 

All ports are non-edge ports. 

Views 

Layer 2 Ethernet interface view, Layer 2 aggregate interface view 

Predefined user roles 

network-admin 

Usage guidelines 

A port directly connecting to a user terminal rather than another device or a shared LAN segment can 
be configured as an edge port. In case the network topology changes, an edge port does not cause 

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands