manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 138

 

130 

After configuring this command, run the 

active region-configuration

 command to activate the 

configured MST region level. 

Examples 

# Set the MSTP revision level of the MST region to 5.  

<Sysname> system-view 

[Sysname] stp region-configuration 

[Sysname-mst-region] revision-level 5 

Related commands 

•

 active 

region-configuration 

•

 check 

region-configuration 

•

 

display stp region-configuration 

•

 instance 

•

 region-name 

•

 vlan-mapping 

modulo 

stp bpdu-protection 

Use 

stp bpdu-protection

 to enable BPDU guard. 

Use 

undo stp bpdu-protection

 to disable BPDU guard. 

Syntax 

stp bpdu-protection

 

undo stp

 

bpdu-protection

 

Default 

BPDU guard is disabled. 

Views 

System view 

Predefined user roles 

network-admin 

Examples 

# Enable BPDU guard. 

<Sysname> system-view 

[Sysname] stp bpdu-protection 

stp bridge-diameter 

Use 

stp bridge-diameter

 to specify the network diameter. 

Use 

undo stp bridge-diameter

 to restore the default.  

Syntax 

stp

 [ 

vlan

 

vlan-id-list

 ] 

bridge-diameter

 

diameter

 

undo stp

 [ 

vlan

 

vlan-id-list

 ] 

bridge-diameter

 

Default 

The network diameter of the switched network is 7.  

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands