HP FlexFabric 7900 Series Command Reference Manual Download Page 19

Page: 19 / 294

return

Use

return

to return to user view from any other view.

Syntax

return

Views

Any view except user view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Usage guidelines

Pressing

Ctrl+Z

has the same effect as the

return

command.

Examples

# Return to user view from FortyGigE 1/0/1 interface view.

[Sysname-FortyGigE1/0/1] return

screen-length disable

Use

screen-length disable

to disable pausing between screens of output for the current session.

Use

undo screen-length disable

to enable pausing between screens of output for the current

session.

Syntax

screen-length disable

undo screen-length disable

Default

The default depends on the configuration of the

screen-length

command in user line view.

The following are default settings for the

screen-length

command:

•

Pausing between screens of output.

•

Displaying up to 24 lines on a screen.

Views

User view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

If you disable pausing between screens of output, all output is displayed. The screen is refreshed
continuously until the final screen is displayed.

Summary of Contents for FlexFabric 7900 Series







































































































































































































































































































Search results

Summary of Contents for FlexFabric 7900 Series

Reviews:

Related manuals for FlexFabric 7900 Series

Brands by name

Popular brands

HP FlexFabric 7900 Series, Command Reference Manual

Search results

Summary of Contents for FlexFabric 7900 Series

Reviews:

Related manuals for FlexFabric 7900 Series

Brands by name

Popular brands