HP Enterprise HPE Edgeline EL8000t User Manual Download Page 46

Page: 46 / 112

• Smart Storage Energy Pack

• TPM or TM firmware

• SAS Programmable Logic Device

• System Programmable Logic Device

• Intelligent Provisioning

• Networking adapters

• NVMe Backplane firmware

• Innovation Engine (IE) firmware

• Drive firmware

• Power Supply firmware

• Embedded Video Controller

• Language packs

• HPE Persistent Memory

Firmware details

The

Installed Firmware page displays the following information for each listed firmware type:

•

Firmware Name—The name of the firmware.

•

Firmware Version—The version of the firmware.

•

Location—The location of the component that uses the listed firmware.

Replacing the active system ROM with the redundant system ROM

Prerequisites

• Host BIOS privilege

• The server supports redundant system ROM.

Procedure

1. Click Firmware & OS Software in the navigation tree.

2. On the Installed Firmware page, click next to the Redundant System ROM details.

iLO prompts you to confirm the request.

3. Click OK.

The change will take effect after the next server reboot.

A server reboot initiated from iLO requires the Virtual Power and Reset privilege.

Updating iLO or server firmware by using the flash firmware feature

You can update firmware from any network client by using the iLO web interface. A signed file is required.

Using HPE iLO 5

Summary of Contents for Enterprise HPE Edgeline EL8000t

















































































































Search results

Summary of Contents for Enterprise HPE Edgeline EL8000t

Reviews:

Related manuals for Enterprise HPE Edgeline EL8000t

Brands by name

Popular brands

HP Enterprise HPE Edgeline EL8000t, User Manual

Search results

Summary of Contents for Enterprise HPE Edgeline EL8000t

Reviews:

Related manuals for Enterprise HPE Edgeline EL8000t

Brands by name

Popular brands