manualshive.com logo in svg

HP EliteBook 1050 G1, Maintenance And Service Manual, Page: 65 / 105

Share
Download
HP EliteBook 1050 G1 Maintenance And Service Manual Download Page 65

Display assembly

NOTE:

Display assemblies are spared at the subcomponent level only. For display assembly spare part 

information, see the individual removal subsections.

To remove the display assembly and access display assembly subcomponents, follow these steps:

1.

Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the 
computer on, and then shut it down through the operating system.

2.

Disconnect the power from the computer by unplugging the power cord from the computer.

3.

Disconnect all external devices from the computer.

4.

Remove the bottom cover (see 

Bottom cover on page 29

).

5.

Remove the battery (see 

Battery on page 31

).

Remove the display assembly:

1.

Remove the two Phillips M2.0×3.0 screws (1) from the display cable connector bracket.

2.

Remove the bracket (2), and then disconnect the display cable from the system board (3).

3.

Disconnect the antennas from the WLAN antenna posts (4).

4.

Disconnect the camera cable from the system board (5).

Brackets are available in the Bracket Kit using spare part number L28674-001.

5.

Remove the five Phillips M2.5×4.5 screws (1) that secure the display to the computer.

6.

Open the computer as far as possible (2).

Component replacement procedures

57

Summary of Contents for EliteBook 1050 G1










































































































Reviews:

No comments