manualshive.com logo in svg

HP E2470A, Manual

Share
Download
HP E2470A Manual Download Page 63

Check the activity indicators for status lines locked in a high or low
state.

Verify that the STAT, DATA, and ADDR format labels have not been
modified from their default values.

Except in certain cases (see page 1-7), these labels must remain as they are
configured by the configuration file. Do not change the names of these labels
or the bit assignments within the labels. Some preprocessors also require
other data labels.  See Chapter 2 for more information.

Verify that all microprocessor caches and memory managers have been
disabled.

In most cases, if the microprocessor caches and memory managers remain
enabled you should still get inverse assembly.  It may be incorrect because a
portion of the execution trace was not visible to the logic analyzer.

Verify that storage qualification has not excluded storage of all the
needed opcodes and operands.

Inverse assembler will not load or run

You need to ensure that you have the correct system software loaded on your
analyzer.

Ensure that the inverse assembler is on the same disk as the
configuration files you are loading.

Configuration files for the state analyzer contain a pointer to the name of the
corresponding inverse assembler. If you delete the inverse assembler or
rename it, the configuration process will fail to load the disassembler.

See Chapter 1 for details.

If You Have a Problem

Inverse assembler will not load or run

A–8

Summary of Contents for E2470A








































































Reviews:

No comments

Brands by name

Popular brands

Load more brands