HP E2470A Manual Download Page 36

Page: 36 / 71

Operating Characteristics

The following operating characteristics are not specifications, but are typical
operating characteristics for the preprocessor interface.

Product Characteristics

Microcontroller Supported

Motorola 68HC16Y1

Package Supported

160-pin PQFP for 68HC16Y1

Logic Analyzer Required

HP 1660A/61A/62A, HP 16550A, HP 16554A,
HP 16555A, or HP 16556A.

Probes Required

Mandatory 4 for state.
Up to 7 for timing.

Accessories Required

HP E5335A Probe Adapter
One 01650-63203 Termination Adapter for each pod
used for timing measurements, or the GP (General
Purpose) probes supplied with your logic analyzer.

Electrical Characteristics

Power Requirements

250 mA typical @ 5 V, supplied by logic analyzer.

Signal Line Loading

8 pF maximum on all signals except CLKOUT which
has 40 pF maximum.

Environmental Characteristics

Temperature

Operating

0 to + 55 degrees C
+32 to +131 degrees F

Nonoperating

-40 to + 75 degrees C
-40 to +167 degrees F

Altitude

Operating

4,600 m
15,000 feet

Nonoperating

15,300 m
50,000 feet

Humidity

Up to 90% noncondensing. Avoid sudden , extreme
temperature changes which could cause
condensation on the circuit board.

Preprocessor Interface Hardware Reference

Operating Characteristics

3–3

Summary of Contents for E2470A








































































Search results

Summary of Contents for E2470A

Reviews:

Related manuals for E2470A

Brands by name

Popular brands

HP E2470A, Manual

Search results

Summary of Contents for E2470A

Reviews:

Related manuals for E2470A

Brands by name

Popular brands