manualshive.com logo in svg

HP E1330A, Service Manual

Share
Download
HP E1330A Service Manual Download Page 16

Shipping Guidelines

Follow the steps in Figure 1-3 to return a Digital I/O module to a
Hewlett-Packard Sales and Support Office or Service Center.

 

 1  Prepare the Digital I/O module

•

Remove user wiring from the module

•

Attach tag to module/pod that identifies

               -  Owner
               -  Model Number/Serial Number
               -  Service Required

•

Place tagged device in approved anti-static bag

 2  Package the Digital I/O module

•

Place packaged Digital I/O module in shipping
carton*

•

Place 75 to 100 mm (3 to 4 inches) of shock-
absorbing material around the Digital I/O module

•

Seal the shipping carton securely

•

Mark the shipping carton FRAGILE

 3  Ship the Digital I/O module to Hewlett-Packard

•

Place address label on shipping carton 

•

Send carton to Hewlett-Packard

* 

We recommend that you use the same shipping materials as those

used in factory packaging (available from Hewlett-Packard). For other

(commercially-available) shipping materials, use a double wall-carton with minimum 2.4 MPa (350 psi) test.

Figure 1-3.  Packaging/Shipping Guidelines

16  General Information

Chapter 1

Summary of Contents for E1330A









































Reviews:

No comments

Brands by name

Popular brands

Load more brands