manualshive.com logo in svg

HP Compaq dx7200 MT, Reference Manual, Page: 84 / 216

Share
Download
HP Compaq dx7200 MT Reference Manual Download Page 84

6–12

390812-001

Service Reference Guide, dx7200

Removal and Replacement Procedures— Microtower (MT) Chassis

4. Before installing an expansion card, remove the expansion slot cover or the existing 

expansion card.

✎

Before removing an installed expansion card, disconnect any cables that may be attached to the 
expansion card.

a.

If you are installing an expansion card in a vacant socket, remove the appropriate 
expansion slot cover on the back of the chassis. Pull the slot cover straight up from the 
socket then away from the inside of the chassis.

b.

If removing a standard PCI expansion card, hold the card at each end, and carefully rock 
it back and forth until the connectors pull free from the socket. Pull the expansion card 
straight up from the socket 

1

 then away from the inside of the chassis 

2

 to release it 

from the chassis frame. Be sure not to scrape the card against the other components.

Summary of Contents for Compaq dx7200 MT

























































































































































































































Reviews:

No comments