manualshive.com logo in svg

HP Compaq dx6100 MT, Reference Manual

Share
Download
HP Compaq dx6100 MT Reference Manual Download Page 199

Service Reference Guide, dx6100

361293-003

C–7

POST Diagnostic Front Panel LEDs and Audible Codes

This section covers the front panel LED codes as well as the audible codes that may occur before 
or during POST that do not necessarily have an error code or text message associated with them.

✎

If you see flashing LEDs on a PS/2 keyboard, look for flashing LEDs on the front panel of the 
computer and refer to the following table to determine the front panel LED codes.

✎

Recommended actions in the following table are listed in the order in which they should be 
performed.

✎

Beeps will occur only for 5 iterations and then stop. LEDs will continue to blink until corrective 
action is taken.

POST Diagnostic Front Panel LEDs and Audible Codes

Activity

Beeps

Possible 

Cause

Recommended Action

Green Power LED 

On.

None

Computer on.

None

Green Power LED 

flashes every two 

seconds.

None

Computer in 

Suspend to RAM 

mode (select 

models only) or 

normal Suspend 

mode.

None required. Press any key or move the 

mouse to wake the computer.

Red Power LED 

flashes two times, 

once every 

second, followed 

by a two second 

pause.

2

Processor 

thermal 

protection 

activated:
A fan may be 

blocked or not 

turning.
OR 
The heatsink/fan 

assembly is not 

properly 

attached to the 

processor. 

Ensure that the computer air vents are not 

blocked and the processor cooling fan is 

running.
Open hood, press power button, and see 

if the processor fan spins. If the processor 

fan is not spinning, make sure the fan's 

cable is plugged onto the system board 

header. Ensure the fan is fully/properly 

seated or installed.
If fan is plugged in and seated properly, 

but is not spinning, then replace processor 

fan.
Reseat processor heatsink and verify that 

the fan assembly is properly attached.
Contact an authorized reseller or service 

provider.

Red Power LED 

flashes three times, 

once every 

second, followed 

by a two second 

pause.

3

Processor not 

installed (not an 

indicator of bad 

processor).

Check to see that the processor is present.
Reseat the processor.

Summary of Contents for Compaq dx6100 MT



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands