HP Compaq dx2100 MT Series Service & Reference Manual Download Page 52

Page: 52 / 116

6–10

404569-001

Service Reference Guide, dx2100 MT

Removal and Replacement Procedures— Microtower (MT) Chassis

6.7.1 Cable Connections

Cable

Cable Designator

Power Supply

System board

Power Supply

1st SATA Hard drive

Power Supply

System board, 24-pin

Power Supply

CPU power, 4-pin

Power Supply

1st Optical drive

Power Supply

2nd Optical drive

Power Supply

2nd SATA Hard drive

Power Supply

DIskette drive

Cable

PCA Designator

Diskette drive

System board

FDD1 (Black)

1st SATA Hard drive

System board

SATA 0 (Black)

2nd SATA Hard drive

System board

SATA 1 (Black)

ODD Data

System board

P10 (Blue)

ODD Audio

System board

CN8 (Black)

Heatsink fan

System board

Secondary system fan

System board

P1 (Brown)

Front power on button

System board

J94

Front I/O USB

System board

Speaker

System board

P11 (White)

Summary of Contents for Compaq dx2100 MT Series





















































































































Search results

Summary of Contents for Compaq dx2100 MT Series

Reviews:

Related manuals for Compaq dx2100 MT Series

Brands by name

Popular brands

HP Compaq dx2100 MT Series, Service & Reference Manual

Search results

Summary of Contents for Compaq dx2100 MT Series

Reviews:

Related manuals for Compaq dx2100 MT Series

Brands by name

Popular brands