manualshive.com logo in svg

HP Compaq dc5100 Series, Service & Reference Manual

The HP Compaq dc5100 Series is a versatile desktop computer designed for performance and productivity. Ensure seamless troubleshooting and maintenance with the comprehensive "Service & Reference Manual". Download this essential manual for free from our website to maximize your experience with this powerful computing solution.

Share
Download
background image

Service Reference Guide, dc5100

376220-001

E–1

E

System Board and Riser Card Reference 

Designators

These reference designators are used on most, but not all, HP system and riser boards.

Designator

Component 

BAT

 

CR1

 

CR2

 

CR3

 

CR4

Battery socket/Battery

 

LED - 5V_Aux(on)/PS_ON(off)

 

Health-LED

 

UID LED

 

Power LED

CR35

 

E14

 

E15

 

E25

 

E49/JP49

Hard drive activity LED

 

Boot block header/jumper

 

Boot block recovery header

 

CPLD programming header

 

Clear Password header/jumper

E50

 

J7

 

J9

 

J10

 

J11

Clear CMOS header

 

RJ45 jack

 

Stacked RJ45/Dual USB

 

Quad stacked USB

 

First IEEE 1394 connector

J12

 

J20 - 29

 

J30

 

J31 - J35

 

J37

Second IEEE 1394 connector

 

PCI slots

 

PCI extender slot (male)

 

PCI Express slots

 

Primary SCSI connector

J38

 

J39

 

J40

 

J41

 

J50

Secondary SCSI connector

 

Stacked parallel/SCSI connector

 

AGP slot

 

x16 PCI Express slot for graphics

 

First parallel port

J51

 

J52

 

J53

 

J54

 

J55

Second parallel port

 

Double-stacked parallel port, Top = Port B, Bottom = Port A

 

Parallel port over single Serial Port

 

Parallel port over Serial Port and Video Port

 

Parallel port over dual VGA ports

J65

 

J66

 

J67

 

J68

 

DVI connector

 

Keyboard connector, PS/2(Closest to power supply)

 

Mouse connector, PS/2

 

Double-stacked mouse/keyboard connector, PS/2

 

Top = Mouse, Bottom = Keyboard 

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

IBM 2179 User Manual preview
2179
Brand: IBM Pages: 120
J.Burrows JBMERGECWS Assembly Instruction Manual preview
JBMERGECWS
Brand: J.Burrows Pages: 24
IBM NetVista S42 Quick Reference preview
NetVista S42
Brand: IBM Pages: 74
Alera ALE-AEWR2B Manual preview
ALE-AEWR2B
Brand: Alera Pages: 12
NEC PC-8201A User Manual preview
PC-8201A
Brand: NEC Pages: 219
Neousys Technology Nuvo-6000 Series User Manual preview
Nuvo-6000 Series
Brand: Neousys Technology Pages: 100
Hitachi MB-6890 Service Manual preview
MB-6890
Brand: Hitachi Pages: 123
Hitachi CE50-10 Instruction Manual preview
CE50-10
Brand: Hitachi Pages: 194
Hitachi HF-BX1000 Instruction Manual preview
HF-BX1000
Brand: Hitachi Pages: 197
Hitachi HF-W2000 30 User Manual preview
HF-W2000 30
Brand: Hitachi Pages: 227
Hitachi H8S/2645 Hardware Manual preview
H8S/2645
Brand: Hitachi Pages: 1153
Acer Aspire M3910 Service Manual preview
Aspire M3910
Brand: Acer Pages: 74
Acer Aspire M3900 Service Manual preview
Aspire M3900
Brand: Acer Pages: 83
Acer Aspire M5810 User Manual preview
Aspire M5810
Brand: Acer Pages: 77
Acer Aspire M5810 Service Manual preview
Aspire M5810
Brand: Acer Pages: 97
Acer Aspire M3710 Service Manual preview
Aspire M3710
Brand: Acer Pages: 73
Acer Aspire T630 User Manual preview
Aspire T630
Brand: Acer Pages: 28
Acer Aspire M5802 Service Manual preview
Aspire M5802
Brand: Acer Pages: 105

Brands by name

Popular brands

Load more brands