manualshive.com logo in svg

HP Compaq dc5100 Series, Service & Reference Manual

The HP Compaq dc5100 Series is a versatile desktop computer designed for performance and productivity. Ensure seamless troubleshooting and maintenance with the comprehensive "Service & Reference Manual". Download this essential manual for free from our website to maximize your experience with this powerful computing solution.

Share
Download
background image

Service Reference Guide, dc5100

376220-001

D–27

Solving Drive Key Problems

Solving Front Panel Component Problems

CD or DVD disc is dirty.

Clean CD or DVD with a CD 
cleaning kit.

Windows does not 
detect the CD-ROM or 
DVD-ROM drive.

1. Use Device Manager to remove 

or uninstall the device in 
question.

2. Restart the computer and let 

Windows detect the device.

Recording audio CDs is 
difficult or impossible.

Wrong or poor quality 
media type.

1. Try using a slower recording 

speed.

2. Verify that you are using the 

correct media for the drive.

3. Try a different brand of media. 

Quality varies widely between 
manufacturers.

Solving CD-ROM and DVD Problems 

(Continued)

Problem

Cause

Solution

Solving Drive Key Problems

Problem

Cause

Solution

Drive key is not seen as a 
drive letter in Windows XP.

The drive letter after the 
last physical drive is not 
available.

Change the default drive letter for 
the Drive key in Windows XP.

The computer boots to DOS 
after making a bootable 
Drive key.

Drive key is bootable.

Install the Drive key after the 
operating system boots.

Solving Front Panel Component Problems

Problem

Cause

Solution

A USB device, headphone, 
or microphone is not 
recognized by the 
workstation.

It is not properly 
connected.

1. Turn off the computer.

2. Reconnect the device to the front of 

the workstation and restart the 
computer.

The device does not 
have power.

If the USB device requires AC power, 
be sure one end is connected to the 
device and one end is connected to a 
live outlet.

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

NComputing L300 Evaluation Manual preview
L300
Brand: NComputing Pages: 16
IBM 2292 Hardware Maintenance Manual preview
2292
Brand: IBM Pages: 230
Aaeon AEC-6860 Manual preview
AEC-6860
Brand: Aaeon Pages: 64
PMC MicroMate -101 User Manual preview
MicroMate -101
Brand: PMC Pages: 126
Digital Equipment PDP-12 Reference Manual preview
PDP-12
Brand: Digital Equipment Pages: 321
Gateway 5694 - GT - 4 GB RAM Reference Manual preview
5694 - GT - 4 GB RAM
Brand: Gateway Pages: 126
Sun Microsystems Sun Ultra 450 Manual preview
Sun Ultra 450
Brand: Sun Microsystems Pages: 45
Onyx MedPC-5500 Manual preview
MedPC-5500
Brand: Onyx Pages: 42
Fujitsu CELSIUS W550 Operating Manual preview
CELSIUS W550
Brand: Fujitsu Pages: 62
Fujitsu CELSIUS W370 E85+ Datasheet preview
CELSIUS W370 E85+
Brand: Fujitsu Pages: 6
Fujitsu CELSIUS W530 Datasheet preview
CELSIUS W530
Brand: Fujitsu Pages: 9
Fujitsu CELSIUS R920 Datasheet preview
CELSIUS R920
Brand: Fujitsu Pages: 9
Fujitsu CELSIUS M4 Series Operating Manual preview
CELSIUS M4 Series
Brand: Fujitsu Pages: 94
Fujitsu CELSIUS W520 Operating Manual preview
CELSIUS W520
Brand: Fujitsu Pages: 69
Fujitsu CELSIUS M770 Operating Manual preview
CELSIUS M770
Brand: Fujitsu Pages: 105
Fujitsu DESKPOWER 500 Series User Manual preview
DESKPOWER 500 Series
Brand: Fujitsu Pages: 80
Fujitsu CELSIUS W510 Operating Manual preview
CELSIUS W510
Brand: Fujitsu Pages: 70
Fujitsu CELSIUS R940 Operating Manual preview
CELSIUS R940
Brand: Fujitsu Pages: 86

Brands by name

Popular brands

Load more brands