manualshive.com logo in svg

HP Compaq dc5100 Series, Service & Reference Manual

The HP Compaq dc5100 Series is a versatile desktop computer designed for performance and productivity. Ensure seamless troubleshooting and maintenance with the comprehensive "Service & Reference Manual". Download this essential manual for free from our website to maximize your experience with this powerful computing solution.

Share
Download
background image

D–22

376220-001

Service Reference Guide, dc5100

Solving Network Problems

These guidelines do not discuss the process of debugging the network cabling.

Solving Network Problems 

Problem

Cause

Solution

Wake-on-LAN feature is 
not functioning.

Wake-on-LAN is not 
enabled.

Use the Network control application 
to enable Wake-on-LAN. 

Network driver does 
not detect network 
controller.

Network controller is 
disabled.

Run Computer Setup and enable 
network controller.
Enable the network controller in the 
operating system via the Device 
Manager.

Incorrect network driver.

Check the network controller 
documentation for the correct driver 
or obtain the latest driver from the 
manufacturer’s Web site.

Network status link light 
does not turn on or it 
never flashes.

✎

The network status 
light should flash 
when there is 
network activity.

No active network is 
detected.

Check cabling and network 
equipment for proper connection.

Network controller is not 
set up properly.

Use the Network control application 
to verify that the device is working 
properly. 

Network driver is not 
properly loaded.

Reinstall network drivers. 

System cannot autosense 
the network.

Disable auto-sensing capabilities 
and force the system into the correct 
operating mode. 

Diagnostics reports a 
failure.

The cable is not securely 
connected.

Ensure that both ends of the data 
cable are securely connected. 

The cable is attached to 
the incorrect connector.

Ensure that the cable is attached to 
the correct connector.

There is a problem with 
the cable or a device at 
the other end of the cable.

Ensure that the cable and device at 
the other end are operating 
correctly.

Network controller 
interrupt is shared with 
an expansion board.

Under the Computer Setup

 

Advanced

 menu, change the 

resource settings for the board.

The network controller 
is defective.

Replace the NIC.

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

Chen Hsong Ai-02 Operation Manual preview
Ai-02
Brand: Chen Hsong Pages: 124
C&T VCO-6020-1050TI User Manual preview
VCO-6020-1050TI
Brand: C&T Pages: 79
S&T kontron KBox B-201-CFL User Manual preview
kontron KBox B-201-CFL
Brand: S&T Pages: 72
Wyse WY-60 User Manual preview
WY-60
Brand: Wyse Pages: 114
eMachines H3120 User Manual preview
H3120
Brand: eMachines Pages: 406
NEC POWERMATE PROFESSIONAL 9000E - SERVICE Service Manual preview
POWERMATE PROFESSIONAL 9000E - SERVICE
Brand: NEC Pages: 206
NEC PowerMate ES SlimLine Series Specifications preview
PowerMate ES SlimLine Series
Brand: NEC Pages: 2
NEC POWERMATE P - SERVICE MANUAL 1995 Service And Reference Manual preview
POWERMATE P - SERVICE MANUAL 1995
Brand: NEC Pages: 171
NEC POWERMATE PRO2180 Manual preview
POWERMATE PRO2180
Brand: NEC Pages: 211
NEC POWERMATE P2166 Manual preview
POWERMATE P2166
Brand: NEC Pages: 221
NEC POWERMATE P ETC User Manual preview
POWERMATE P ETC
Brand: NEC Pages: 177
NEC POWERMATE P2166 Service Manual preview
POWERMATE P2166
Brand: NEC Pages: 219
NEC POWERMATE NETPC System Administrator Manual preview
POWERMATE NETPC
Brand: NEC Pages: 125
NEC POWERMATE PRO150 Manual preview
POWERMATE PRO150
Brand: NEC Pages: 167
NEC PowerMate Pro 2180 User Manual preview
PowerMate Pro 2180
Brand: NEC Pages: 211
NEC POWERMATE PROFESSIONAL 9000E - SERVICE User Manual preview
POWERMATE PROFESSIONAL 9000E - SERVICE
Brand: NEC Pages: 283
NEC POWERMATE PRO150 Service Manual preview
POWERMATE PRO150
Brand: NEC Pages: 167
NEC POWERMATE PROFESSIONAL 9000 - SERVICE Service Manual preview
POWERMATE PROFESSIONAL 9000 - SERVICE
Brand: NEC Pages: 296

Brands by name

Popular brands

Load more brands