manualshive.com logo in svg

HP Compaq dc5100 Series, Service & Reference Manual

The HP Compaq dc5100 Series is a versatile desktop computer designed for performance and productivity. Ensure seamless troubleshooting and maintenance with the comprehensive "Service & Reference Manual". Download this essential manual for free from our website to maximize your experience with this powerful computing solution.

Share
Download
background image

C–6

376220-001

Service Reference Guide, dc5100

2000-Master Boot 
Record Hard Drive has 
Changed.

The current bootable hard 
drive is not the same as 
the one that was present 
when MBR security was 
enabled.

Run Computer Setup and either disable 
MBR security or save the MBR of the 
current bootable disk.

Invalid Electronic Serial 
Number.

Electronic serial number 
has become corrupted.

Run Computer Setup. If Setup already 
has data in the field or will not allow the 
serial number to be entered, download 
from http://www.hp.com and run 
SP5572.EXE (SNZERO.EXE).
Run Computer Setup and try to enter 
serial number under Security, System ID, 
then save changes.

Network Server Mode 
Active and No 
Keyboard Attached

Keyboard failure while 
Network Server Mode 
enabled.

Reconnect keyboard with computer 
turned off.
Check connector for bent or missing 
pins.
Ensure that none of the keys are 
depressed.
Replace keyboard.

Parity Check 2.

Parity RAM failure.

Run Computer Setup and Diagnostic 
utilities.

POST Error Messages 

Screen Message

Probable Cause

Recommended Action

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

Radio Shack 4 Quick Reference preview
4
Brand: Radio Shack Pages: 31
IBASE Technology CSB200-818 User Manual preview
CSB200-818
Brand: IBASE Technology Pages: 68
Clarke CWB450WS Assembly Instructions Manual preview
CWB450WS
Brand: Clarke Pages: 8
Asus TW100-E6 Configuration Manual preview
TW100-E6
Brand: Asus Pages: 18
Asus TW300-E5/PI4 User Manual preview
TW300-E5/PI4
Brand: Asus Pages: 174
Asus TS700-E6/RS8 User Manual preview
TS700-E6/RS8
Brand: Asus Pages: 166
Dell Inspiron 5570 Setup And Specifications preview
Inspiron 5570
Brand: Dell Pages: 27
Dell OptiPlex 270 Service Manual preview
OptiPlex 270
Brand: Dell Pages: 25
Dell OptiPlex 980 - Desktop Administrator'S Manual preview
OptiPlex 980 - Desktop
Brand: Dell Pages: 101
Lenovo 8822 Hardware Replacement Manual preview
8822
Brand: Lenovo Pages: 18
Lenovo 8807D5U Brochure preview
8807D5U
Brand: Lenovo Pages: 4
Lenovo 8808D2U Brochure preview
8808D2U
Brand: Lenovo Pages: 4
Lenovo 8991DFU Brochure preview
8991DFU
Brand: Lenovo Pages: 2
Lenovo 90BX E50-00 Series Hardware Maintenance Manual preview
90BX E50-00 Series
Brand: Lenovo Pages: 49
Lenovo 8820ADU User Manual preview
8820ADU
Brand: Lenovo Pages: 82
Lenovo 892204U - C200 8922 - Celeron M 1.6 GHz Manual preview
892204U - C200 8922 - Celeron M 1.6 GHz
Brand: Lenovo Pages: 56
Lenovo 90B6 [H50-50 ES] User Manual preview
90B6 [H50-50 ES]
Brand: Lenovo Pages: 63
Lenovo 821532U - ThinkCentre M52 - 8215 Hardware Maintenance Manual preview
821532U - ThinkCentre M52 - 8215
Brand: Lenovo Pages: 530

Brands by name

Popular brands

Load more brands