manualshive.com logo in svg

HP Compaq dc5100 Series, Service & Reference Manual

The HP Compaq dc5100 Series is a versatile desktop computer designed for performance and productivity. Ensure seamless troubleshooting and maintenance with the comprehensive "Service & Reference Manual". Download this essential manual for free from our website to maximize your experience with this powerful computing solution.

Share
Download
background image

Service Reference Guide, dc5100

376220-001

7–25

Removal and Replacement Procedures— Small Form Factor (SFF) Chassis

7.9.4 Primary Hard Drive 

1. If you have locked the Smart Cover Lock, use Computer Setup to unlock the lock (

Section 

7.2, “Unlocking the Smart Cover Lock”

).

2. Prepare the computer for disassembly (

Section 7.1, “Preparation for Disassembly”

).

3. Remove the computer cover (

Section 7.4, “Computer Cover”

).

4. Press down on the green latch located on the front of the chassis next to the optical drive 

1

 

and slide the drive cage forward 

2

 to its fully extended position. This will give you access to 

the cable connectors on the primary hard drive.

✎

It is not necessary to remove the optical drive.

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

Saint Song Corporation TX-3 User Manual preview
TX-3
Brand: Saint Song Corporation Pages: 33
IBM PC 300GL Type 6561 Technical Information Manual preview
PC 300GL Type 6561
Brand: IBM Pages: 66
Avid Technology Dell T7600 Configuration Manuallines preview
Dell T7600
Brand: Avid Technology Pages: 23
IBM Aptiva 2165 Hardware Maintenance Service preview
Aptiva 2165
Brand: IBM Pages: 167
Vivo DESK-V000A Instruction Manual preview
DESK-V000A
Brand: Vivo Pages: 3
Casio FX-890P Owner'S Manual preview
FX-890P
Brand: Casio Pages: 126
Asus BT14675 User Manual preview
BT14675
Brand: Asus Pages: 16
Dell Precision 370 - SX280 Ultra Small Form Factor Quick Reference Manual preview
Precision 370 - SX280 Ultra Small Form Factor
Brand: Dell Pages: 162
Partners PC Setup Manual preview
PC
Brand: Partners Pages: 3
Giada F105D User Manual preview
F105D
Brand: Giada Pages: 41
BPC 8590 User Manual preview
8590
Brand: BPC Pages: 81
Edirol Direct Linear DV-7DL Pro Owner'S Manual preview
Direct Linear DV-7DL Pro
Brand: Edirol Pages: 372
Xitrix DeskFrame MX-910 User Manual preview
DeskFrame MX-910
Brand: Xitrix Pages: 89
Shuttle XPC slim XH510G2 Quick Manual preview
XPC slim XH510G2
Brand: Shuttle Pages: 3
Dell EMC P92F Service Manual preview
P92F
Brand: Dell EMC Pages: 60
VAIO Slimtop PCV-LX810 Upgrading And Maintaining preview
Slimtop PCV-LX810
Brand: VAIO Pages: 8
EverFocus eIVP-CML-AI-D0000 User Manual preview
eIVP-CML-AI-D0000
Brand: EverFocus Pages: 19
IC nexus SBC21 Series Quick Start Manual preview
SBC21 Series
Brand: IC nexus Pages: 43

Brands by name

Popular brands

Load more brands