manualshive.com logo in svg

HP Compaq dc5000 MT, Reference Manual, Page: 34 / 180

Share
Download
HP Compaq dc5000 MT Reference Manual Download Page 34

3–6

360201-002

Service Reference Guide, dc5000

Desktop Management

3.4.4 Replicating the Setup

This procedure gives an administrator the ability to quickly and easily copy one setup 
configuration to other computers of the same model. To replicate the setup:

1. Access the Computer Setup Utilities (F10) menu. 

2. Click 

File > Save to Diskette.

 Follow the instructions on the screen.

✎

This requires a diskette drive or a supported USB flash media device, such as Drive Key.

3. To replicate the configuration, click 

File > Restore

 

from Diskette

, and follow the 

instructions on the screen.

System Software Manager (SSM) may also be used to distribute setup configurations to multiple 
computers. For more information, see

 http://www.hp.com/go/ssm

.

3.4.5 Dual-State Power Button

With Advanced Configuration and Power Interface (ACPI) enabled for Windows 2000 and 
Windows XP, the power button can function either as an on/off switch or as a suspend button. 
The suspend feature does not completely turn off power, but instead causes the computer to enter 
a low-power standby. This allows you to quickly power down without closing applications and 
to quickly return to the same operational state without any data loss.

To change the power button’s configuration, complete the following steps:

1. In Windows 2000, left click on the 

Start Button,

 then select 

Settings > Control Panel > 

Power Options.

In Windows XP, left click on the 

Start Button,

 then select 

Control Panel > Power 

Options.

2. In the 

Power Options Properties,

 select the 

Advanced

 tab.

3. In the 

Power Button

 section, select the desired power button setting.

Keyboard Light Combinations Used by Boot Block ROM 

Failsafe Boot 

Block Mode

Keyboard 

LED Color

Keyboard 

LED Activity

State/Message

Num Lock

Green

On

ROMPaq diskette not present, is bad, or 
drive not ready.

Caps Lock

Green

On

Enter password.

Num, Caps, 
Scroll Lock

Green

Blink on in 
sequence, 
one-at-a-time— 
N,C,SL

Keyboard locked in network mode.

Num, Caps, 
Scroll Lock

Green

On

Boot Block ROM Flash successful. Turn 
power off, then on to reboot.

✎

Diagnostic lights do not flash on USB keyboards.

Summary of Contents for Compaq dc5000 MT





















































































































































































Reviews:

No comments