HP BCDVideo BCD108 User Manual Download Page 10

Page: 10 / 162

Component identification 10

Power fault LEDs

The following table provides a list of power fault LEDs, and the subsystems that are affected. Not all
power faults are used by all servers.

Subsystem

LED behavior

System board

1 flash

Processor

2 flashes

Memory

3 flashes

Riser board PCIe slots

4 flashes

FlexibleLOM

5 flashes

Removable HPE Flexible Smart Array
controller/Smart SAS HBA controller

6 flashes

System board PCIe slots

7 flashes

Power backplane or storage backplane

8 flashes

Power supply

9 flashes

Systems Insight Display LEDs

The Systems Insight Display LEDs represent the system board layout. The display provides status for all
internal LEDs and enables diagnosis with the access panel installed. To view the LEDs, access the
Systems Insight Display.

Description

Status

Processor LEDs

Off = Normal
Amber = Failed processor

DIMM LEDs

Off = Normal
Amber = Failed DIMM or configuration issue

Fan LEDs

Off = Normal
Amber = Failed fan or missing fan

Summary of Contents for BCDVideo BCD108



































































































































































Search results

Summary of Contents for BCDVideo BCD108

Reviews:

Related manuals for BCDVideo BCD108

Brands by name

Popular brands

HP BCDVideo BCD108, User Manual

Search results

Summary of Contents for BCDVideo BCD108

Reviews:

Related manuals for BCDVideo BCD108

Brands by name

Popular brands