manualshive.com logo in svg

HP Aruba 7010 Series, Installation Manual, Page: 22 / 28

Share
Download
HP Aruba 7010 Series Installation Manual Download Page 22

22

| Installation

Aruba 7010 Series Controller

| Installation Guide

Figure 11  

Wall Mounting 

Connecting and Disconnecting the AC Power Cord

Once you have installed the 7010 controller, you are ready to power On the device. The 7010 

controller is not equipped with an On/Off switch. The device will power On when the AC power cord 

is connected to the power supply and an AC power outlet.

Connecting the AC Power Cord

To connect the AC power cord to the 7010 controller:
1. Lift the power cord retaining clip so that it is not blocking the AC power connector.
2. Insert the coupler end of the AC power cord into the AC power connector on the power supply 

module.

3. Lower the power cord retaining clip over the AC power cord.
The 7010 controller should now be receiving power. 

Disconnecting the AC Power Cord

To disconnect the AC power cord from the 7010 controller:
1. Lift the power cord retaining clip off the AC power cord.
2. Pull the AC power cord from the power supply module.

Summary of Contents for Aruba 7010 Series





























Reviews:

No comments