HP A7500 Series Command Reference Manual Download Page 83

Page: 83 / 222

[Sysname] tftp client source ip 2.2.2.2

# Specify the IP address of interface VLAN-interface 1 as the source IP address of packets sent to a TFTP

server.

<Sysname> system-view

[Sysname] tftp client source interface vlan-interface 1

tftp ipv6

Syntax

tftp ipv6

tftp-ipv6-server

[

-i

interface-type interface-number

] {

get

put

}

source-filename

[

destination-filename

] [

vpn-instance

vpn-instance-name

]

View

User view

Default level

3: Manage level

Parameters

tftp-ipv6-server

: IPv6 address or host name (a string of 1 to 46 characters) of a TFTP server.

-i

interface-type interface-number

: Specifies an output interface by its type and number. This parameter

can be used only when the TFTP server address is a link local address and the specified output interface

has a link local address. For the configuration of a link local address, see IPv6 basics configuration in the

Layer 3—IP Services Configuration Guide

get

: Downloads a file.

put

: Uploads a file.

source-file

: Source filename.

destination-file

: Destination filename. If it is not specified, this filename is the same as the source

filename.

vpn-instance

vpn-instance-name

: Specifies the MPLS L3 VPN that the TFTP server belongs to. The

vpn-instance-name

argument is a case-sensitive string of 1 to 31 characters.

Description

Use the

tftp ipv6

command to download a specified file from a TFTP server or upload a specified local

file to a TFTP server in an IPv6 network.

Examples

# Download

filetoget.txt

from the TFTP server.

<Sysname> tftp ipv6 fe80::250:daff:fe91:e058 -i Vlan-interface 1 get filetoget.txt

...

File will be transferred in binary mode

Downloading file from remote TFTP server, please wait....

TFTP: 411100 bytes received in 2 second(s)

File downloaded successfully.

Summary of Contents for A7500 Series































































































































































































































Search results

Summary of Contents for A7500 Series

Reviews:

Related manuals for A7500 Series

Brands by name

Popular brands

HP A7500 Series, Command Reference Manual

Search results

Summary of Contents for A7500 Series

Reviews:

Related manuals for A7500 Series

Brands by name

Popular brands