HP A7500 Series Command Reference Manual Download Page 37

Page: 37 / 222

Examples

# Enable the modem to accept both incoming and outgoing calls.

<Sysname> system-view

System View: return to User View with Ctrl+Z.

[Sysname] user-interface aux 0

[Sysname-ui-aux0] modem both

modem auto-answer

Syntax

modem auto-answer
undo modem auto-answer

View

AUX interface view

Default level

2: System level

Parameters

None

Description

Use the

modem auto-answer

command to configure the switch-side modem to operate in the

auto-answer mode.
Use the

undo modem auto-answer

command to restore the default.

By default, the switch-side modem operates in the manual answer mode.

Examples

# Configure the switch-side modem to operate in the auto-answer mode.

<Sysname> system-view

System View: return to User View with Ctrl+Z.

[Sysname] user-interface aux 0

[Sysname-ui-aux0] modem auto-answer

modem timer answer

Syntax

modem timer answer

seconds

undo modem timer answer

View

AUX interface view

Default level

2: System level

Parameters

seconds

: Timeout time in seconds, in the range of 1 to 60. The default value is 30 seconds.

Summary of Contents for A7500 Series































































































































































































































Search results

Summary of Contents for A7500 Series

Reviews:

Related manuals for A7500 Series

Brands by name

Popular brands

HP A7500 Series, Command Reference Manual

Search results

Summary of Contents for A7500 Series

Reviews:

Related manuals for A7500 Series

Brands by name

Popular brands