manualshive.com logo in svg

HP A7500 Series, Command Reference Manual

The HP A7500 Series Configuration Manual is a comprehensive resource for users looking to optimize the performance of their HP A7500 Series product. This manual can be easily downloaded for free from manualshive.com, providing step-by-step instructions and valuable insights for efficient configuration and enhanced functionality.

Share
Download
background image

 

204 

reboot

: Specifies that when a software exception occurs on an MPU, the switch automatically reboots the 

MPU to recover it from the error condition. 

Description 

Use the 

system-failure

 command to configure the software exception handling method for MPUs. 

By default, an MPU reboots to recover from a software exception condition.  
In an IRF fabric, the software exception handling method applies to all member switches.  

 

 

NOTE: 

An LPU always reboots to recover from a software exception condition.  

 

Examples 

# Set the software exception handling method to reboot for MPUs. 

<Sysname> system-view 

[Sysname] system-failure reboot 

temperature-limit 

Syntax 

In standalone mode:

 

temperature-limit

 

slot 

slot-number

 

hotspot 

sensor-number

 

lowerlimit warninglimit 

[ 

alarmlimit

 ] 

undo temperature-limit slot 

slot-number

 

hotspot 

sensor-number 

In IRF mode: 

temperature-limit

 

chassis

 

chassis-number

 

slot 

slot-number

   

hotspot 

sensor-number

 

lowerlimit 

warninglimit 

[ 

alarmlimit

 ] 

undo temperature-limit chassis

 

chassis-number

 

slot 

slot-number

 

hotspot 

sensor-number 

 

View 

System view 

Default level 

2: System level 

Parameters 

chassis 

chassis-number

: Specifies an IRF member switch. The 

chassis-number

 argument represents the IRF 

member ID of the switch. (In IRF mode)

 

slot 

slot-number

: Specifies a card in the specified switch. The 

slot-number

 argument represents the slot 

number of the card.  

hotspot

: Specifies a hotspot sensor. Hotspot sensors are placed near major heat sources, for example, 

chips, to monitor their temperature.

 

sensor-number

: Specifies a sensor number, an integer that increases from 1.  

lowerlimit

: Low temperature threshold in Celsius degrees. The value ranges from –5°C to +5°C (23°F to 

41°F). 

Summary of Contents for A7500 Series































































































































































































































Reviews:

No comments

Related manuals for A7500 Series

Cables to Go 40020 Instruction Manual preview
40020
Brand: Cables to Go Pages: 4
Magnetrol TK1 Operating Manual preview
TK1
Brand: Magnetrol Pages: 12
Magnimage V4 Series User Manual preview
V4 Series
Brand: Magnimage Pages: 53
Meridian SX-4FX Series Installation & Operation Instructions preview
SX-4FX Series
Brand: Meridian Pages: 16
IDEM SAFETY SWITCHES KLM-P2L Operating Instructions preview
KLM-P2L
Brand: IDEM SAFETY SWITCHES Pages: 2
Woxcon MUH44A-H2 User Manual preview
MUH44A-H2
Brand: Woxcon Pages: 42
Blackmagicdesign Universal Videohub 288 Installation And Operation Manual preview
Universal Videohub 288
Brand: Blackmagicdesign Pages: 107
CYP OR-44VWC Operation Manual preview
OR-44VWC
Brand: CYP Pages: 28
Pakedge SE-18 Quick Start Manual preview
SE-18
Brand: Pakedge Pages: 12
ADS Technologies USBH-604 Connection Manual preview
USBH-604
Brand: ADS Technologies Pages: 2
nedis VMAT3482AT Manual preview
VMAT3482AT
Brand: nedis Pages: 24
Omega OM-ESW-105-POE User Manual preview
OM-ESW-105-POE
Brand: Omega Pages: 17
Accton Technology EH2045S Quick Start Manual preview
EH2045S
Brand: Accton Technology Pages: 8
Lanpro SW2400S User Manual preview
SW2400S
Brand: Lanpro Pages: 16
J-Tech Digital JTD-2886 User Manual preview
JTD-2886
Brand: J-Tech Digital Pages: 81
ATEN ES0152 User Manual preview
ES0152
Brand: ATEN Pages: 300
Ubiquiti EdgeSwitch 48 Quick Start Manual preview
EdgeSwitch 48
Brand: Ubiquiti Pages: 24
C4i HDP-MXB88DA User Manual preview
HDP-MXB88DA
Brand: C4i Pages: 22

Brands by name

Popular brands

Load more brands