HP 8920A User Manual Download Page 441 | Manualshive

Page: 441 / 658

background image

441

Chapter 12, I/O Configure Screen

Field Descriptions

Save/Recall

This field specifies which memory device the Test Set accesses when the save and
recall functions are used.

•

Internal

is a section of internal RAM. RAM is also used for running IBASIC

programs, which may require you to delete the Save/Recall registers if the program is
very large.

•

Card

is the front-panel MEMORY CARD slot. A

Save/Recall Device is not

Present

message is displayed if you try to save or recall an instrument setup when

a write-able memory card is not installed in the Test Set.

•

RAM

refers to RAM disks that you can create on internal RAM. Refer to the

Programmer’s Guide for information on creating RAM Disks. This is part of the same
memory used when “internal” is specified, and may have to be erased when loading
very large IBASIC programs. A

Save/Recall Device is not initialized

message is displayed if you try to save or recall an instrument setup when a RAM disk
has not been created.

•

Disk

is used with external disk drives. The

Mode

field must be set to

Control

to

access the drive. Also, the HP-IB address of the drive must be entered in the

External Disk Specification

field of the TESTS (External Devices) screen.

Serial Baud

This field selects the baud rate for serial communications when using the rear-
panel serial port

1

. Selecting this field displays a list of baud rate choices.

This setting is maintained after the instrument is turned off.

1.

Optional on some Test Set models.

«
...
439
440
441
442
443
...
»

Summary of Contents for 8920A



















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8920A

Brand: ParaBody Pages: 6

Brand: Sailmon Pages: 10

Brand: B&W Tek Pages: 12

Brand: b&o Pages: 46

Brand: Parker Pages: 5

Brand: Bacharach Pages: 31

Brand: Backyard Play Systems Pages: 52

Brand: Backyard Play Systems Pages: 19

Brand: Backyard Play Systems Pages: 44

Brand: Bacharach Pages: 2

Brand: Parker Research Corp Pages: 4

Brand: Eastwood Pages: 20

Brand: Daihan Scientific Pages: 43

Brand: Federal Signal Corporation Pages: 12

Brand: Gaspardo Pages: 16

Brand: Gastrodomus Pages: 4

Brand: HANYOUNG NUX Pages: 2

Brand: Gastrodomus Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands