HP 8920A User Manual Download Page 150 | Manualshive

Page: 150 / 658

background image

150

S:\HP892XX\USRGUIDE\manual\callscrn.fb

Chapter 6, Call Processing Subsystem

Using the CALL CONTROL Screen to Test Call Processing Functions

Send an Alert Order to a Mobile Station

Ensure that the Test Set is in the connected state.

See "Page a Mobile Station" on page

for information on how to bring a mobile station up on a voice channel.

1. If the CALL CONTROL screen is not displayed, select

CALL CNTL

under the

To

Screen

menu. The CALL CONTROL screen will be displayed.

2. Select the

Order

field. A

Choices:

menu is displayed showing the various orders

which can be sent to the mobile station. Select the

Mainten

order from the list of

choices. The Test Set will then go into the

Access

state and signal the mobile station

with a maintenance order. If the mobile station is responding properly it will go into its
maintenance state as defined by the applicable cellular system standard. The left-hand
fields in the

Voice Channel Assignment

section will display a ‘-’ while the Test

Set is in the access state.

3. Select the

Order

field. A

Choices:

menu is displayed showing the various orders

which can be sent to the mobile station. Position the cursor next to the

Alert

order and

select it. The Test Set will then signal the mobile station with an alert order. If the
mobile station is responding properly it will alert (that is, it will ring). Press the SEND
key on the mobile station to respond to the alert order. The mobile station should exit
the maintenance state. The Test Set, upon detecting that the mobile station has exited
the maintenance state, will return to the

Connect

state and the left-hand subfields in

the

Voice Channel Assignment

section will be updated with the current voice

channel assignment information.

NOTE:

Applicable cellular system standards may specify a time-out period for the maintenance state.
If an Alert order is not received during this time-out period the mobile station may take some
action as defined by the standard. One such action might be to terminate the voice channel
connection. Refer to the applicable cellular system standard for specific information

«
...
148
149
150
151
152
...
»

Summary of Contents for 8920A



















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8920A

Brand: Haaga Pages: 31

Brand: Yamaha Pages: 46

Brand: R&S Pages: 2677

Brand: Safety 1st Pages: 4

Brand: Safety Engineering Pages: 5

LED Street Bar 16x3W RGB IP65

Brand: Varytec Pages: 9

Brand: VARILITE Pages: 8

EVENTPROFILE VL800

Brand: Vari Lite Pages: 34

Optica 30 Series

Brand: Varex Imaging Pages: 36

Brand: ABB Pages: 33

Brand: X-METAL Pages: 135

Brand: Nady Audio Pages: 2

Wallach UltraFreeze

Brand: Cooper Surgical Pages: 4

Brand: Life Fitness Pages: 45

VADA TWIN MOTOR MACERATOR

Brand: Reece Pages: 7

Brand: Hella Gutmann Pages: 48

Brand: Sammode Pages: 12

Brand: Sanela Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands