HP 85106D Manual Download Page 90 | Manualshive

Page: 90 / 244

background image

HP 85106D mm-Wave System

3-5

Performance Verification

Installation of HP-BASIC and Performance Verification Software

Procedure

1. Select the equipment listed previously or select the equipment for your

system. The CRT displays a highlighted field around the active
selection. Use the {

NEXT

} and {

PREVIOUS

} keys to change the selection

in the highlighted area as needed. Continue making selections to get the
correct hardware configuration.

2. Press the {

DONE

} softkey to load the program. The MAIN menu is

returned to the controller display. The program remembers the last
system configuration you selected and when you run the program
again (without turning the controller OFF), the same configuration
appears on the display. You can reset the configuration by pressing
{

PROGRAM RESET

} in the SYSTEM CONFIGURATION menu.

3. Have the following kits and disks ready to use:

•

Calibration kit and its disk. The model number of the calibration kit
must match the one you selected in the Configuration menu.

•

Verification kit and its disk. The model number of the verification kit
must match the one you selected in the Configuration menu.

NOTE

Be sure the controller is connected to the HP 8510C rear panel HP-IB
connector. Also, the HP 8510 must be warmed-up for one hour before
verification.

4. Press [

SYSTEM

] {

HP-IB configure

} {

HP-IB uses USR PRESET

} to send

the preset command over HP-IB to USER PRESET.

5. Press {

VERIFY SYSTEM

}. If the program acknowledges the system over

HP-IB, the System Performance Verification Menu is displayed on the
controller.

6. Press {

SERIAL NUMBERS

}. Enter the serial numbers and the NIST numbers

only if you want them to appear on the printout of your performance test
results for each verification device. The serial numbers are usually
located on the instrument rear panels. Locate NIST test numbers on the
Certificate of Calibration that accompanies your verification kit.

7. When you are finished with this menu press {

DONE

}.

You are returned to the System Performance Verification Menu. Press
{

SYSTEM CAL

}. The configuration information is displayed. Be sure it agrees

with the system you plan to verify. If it does, press {

RESUME

}to continue. If

not, go back to the Hardware Configuration Menu and edit the configuration
listing to correct it.

«
...
88
89
90
91
92
...
»

Summary of Contents for 85106D





















































































































































































































































Reviews:

No comments

Related manuals for 85106D

Brand: Eagle Eye Pages: 3

Brand: VALTRONICS Pages: 13

Brand: JIANGSU Pages: 8

Brand: R.M. Young Pages: 2

Brand: Halcyon Pages: 36

Brand: Oakton Pages: 69

Brand: ICM Controls Pages: 8

Brand: Valhalla Scientific Pages: 43

Brand: +GF+ Pages: 8

Brand: AR Pages: 8

Brand: ILX Lightwave Pages: 126

Brand: Kobold Pages: 55

Brand: Interacoustics Pages: 54

Brand: PCB Piezotronics Pages: 10

Brand: Bühler technologies Pages: 33

Brand: Sensitech Pages: 2

Brand: Endress+Hauser Pages: 24

Brand: JBM Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands