manualshive.com logo in svg

HP 85106D, Manual, Page: 87 / 244

Share
Download
HP 85106D Manual Download Page 87

3-2

HP 85106D mm-Wave System

Performance Verification

Installation of HP-BASIC and Performance Verification Software

Installation of HP-BASIC and Performance

Verification Software

NOTE 

Always use the highest numbered software version for performance
verification.

Installing on a PC

The DOS version of the software runs on an INTEL 486 PC or higher, and
must have at least four megabytes of available memory. The PC is also
required to have a HP-IB card to communicate to the HP 8510 System.

NOTE 

Refer to the HP BASIC for Windows, Installing and Using Guide for the
details of installing a configuring HP BASIC on a PC.

1. Install HP BASIC on PC by following the instructions on the 1st disk.

The program will guide you through the installation process.

2. Install the Performance and Verification software by following the

instructions on the disk lable. The installation program will lead you
through the installation and create the program group which includes the
specs and verification icon.

3. Click the mouse on the “Specs and Verification” icon to run the

program. The first time you start the program you will get the following
warning message:

A valid HPBW GPIB (HP-IB) driver for your board (if any) has not been loaded.

You can run the Specifications and Uncertainty portions of the HP 8510 software

but cannot run the Verification portion as this requires GPIB or:

To load the correct driver EDIT this program and Remove the “!” from in

front of the LOAD statement for your GPIB board.

After editing, type RE-STORE “AUTOST” to store the modified program . Then,

close this window and re-select the Specifications Verification icon to

re-run the program. The HP 8510 software should now load and run.

Follow the instructions in the above warning message to edit AUTOST file if
you need to run the verification.

Summary of Contents for 85106D





















































































































































































































































Reviews:

No comments