HP 85106D Manual Download Page 194

Page: 194 / 244

HP 85106D mm-Wave System

6-29

HP 85105A mm-Wave Controller

LO Input at Rear Panel

Procedure 4

Figure 6-14 Rear Panel LO Input

1. Run the system software and select {

HIGHBAND

} to make the mm-wave

controller active.

2. Choose a power meter that covers the 4 to 6 GHz frequency range

(HP 436A meter and HP 8485A sensor). Calibrate the power meter and
attach a 3.5 mm (female to female) adapter to the sensor.

3. Disconnect the LO source cable from the back of the instrument and

attach the power sensor to the LO cable. Select {

SINGLE POINT MODE

}

from the [

STIMULUS

] menu, then using the RPG knob, slowly scan over

the frequency band. The power level should be 0 to +2 dBm.

Summary of Contents for 85106D





















































































































































































































































Search results

Summary of Contents for 85106D

Reviews:

Brands by name

Popular brands

HP 85106D, Manual

Search results

Summary of Contents for 85106D

Reviews:

Brands by name

Popular brands