HP 85106D Manual Download Page 130

Page: 130 / 244

HP 85106D mm-Wave System

5-13

HP 85104A Test Set Module

Troubleshooting Procedures

Switching Mixers
(A11, A12)

Procedure 3

Before beginning this procedure, turn power to the HP 85105A mm-wave
controller OFF. Disconnect the HP 85104A from the HP 85105A. This
procedure assumes that the isolators are located in their original modules.

Refer to the step references in Figure 5-11 on page 5-32.

1. Remove the IF and LO cables from the mixer inputs (Step 7 and

Step 13).

2. Disconnect the isolator at the mixer interface (Step 15 and Step 16).

3. Remove the mixer bracket (Step 14).

4. Replace the mixer with the mixer from the opposite auxiliary arm or

with a mixer from another test set module.

5. Attach the new mixer to the isolator and connect the IF and LO input

cables. Be sure to use correct waveguide connection techniques (refer to
“Waveguide Connections” on page 2-9 for waveguide connection
information).

6. Connect the mixer clamp.

7. Reconnect the cables from the HP 85104A to the HP 86105A. Turn the

HP 85105A ON. Recheck the unratioed power levels (refer to

“Procedure 1” on page 5-11).

8. Return to the troubleshooting flowchart.

Summary of Contents for 85106D





















































































































































































































































Search results

Summary of Contents for 85106D

Reviews:

HP 85106D, Manual, Page: 130 / 244

Search results

Summary of Contents for 85106D

Reviews: