manualshive.com logo in svg

HP 85106D, Manual, Page: 104 / 244

Share
Download
HP 85106D Manual Download Page 104

HP 85106D mm-Wave System

4-11

Service and Troubleshooting

Symptomatic Failure Types

Symptomatic Failure Types

Refer to the following heading listed that most closely represents the
instrument problem (obvious or not). They are suggested courses of action
specific to the failure symptom.

•

Millimeter-Wave, Phase Lock, Power Loss, or Frequency Related
Problems.

Check Unratioed
Power Levels

Refer to the test titled “Check Unratioed Power Levels” on page 4-19.

•

Microwave, Phase Lock, Power Loss, or Frequency Related Problems
When Using the Optional HP 8517B Test Set.

When Using the
Optional HP 8517B
Test Set

To help locate the faulty instrument, the service adapter (HP part number
85102-60210) is used to emulate the operation of the source and test set and
check unratioed power levels into the HP 85102 IF/Detector.

NOTE 

When checking any unratioed power levels, turn the HP 8510 averaging
OFF. Refer to “Unratioed Power Test” in the HP 8517B Operating and
Service Manual. This procedure allows you to check individually the output
power level of each test set sampler/mixer assembly and its associated IF
amplifier. Depending upon the test outcome, the procedure directs you to the
most likely cause of failure.

Summary of Contents for 85106D





















































































































































































































































Reviews:

No comments