Home
/
HP
/
5800
/
Command Reference Manual

HP 5800, Command Reference Manual, Page: 343 / 396

Share

Page: 343 / 396

HP 5800 Command Reference Manual Download Page 343

334

association between a VPN instance and its reserved VLAN, you need to delete the VPN instance,
recreate it, and then specify another reserved VLAN for it.

Syntax

reserve-vlan

vlan-id

View

VPN instance view

Default level

2: System level

Parameters

vlan-id

: Specifies the ID of the VLAN to be specified as the reserved VLAN of the VPN instance, ranging

from 1 to 4094.

Examples

# Specify VLAN 100 as the reserved VLAN of VPN instance

vpn1

.

<Sysname> system-view

[Sysname] ip vpn-instance vpn1

[Sysname-vpn-instance-vpn1] reserve-vlan 100

reset bgp vpn-instance

Description

Use the

reset bgp vpn-instance

command to reset the BGP connections of a VPN instance.

Syntax

reset bgp vpn-instance

vpn-instance-name

{

as-number

|

ip-address

|

all

|

external

|

group

group-name

}

View

User view

Default level

1: Monitor level

Parameters

vpn-instance-name

: Resets BGP connections with the peers in a VPN instance. VPN instance name is a

case-sensitive string of 1 to 31 characters.

as-number

: Resets BGP connections with the peers in an AS identified by this number. This parameter is

ranging from 1 to 4,294,967,295.

ip-address

: Resets the connection with a BGP peer identified by this IP address.

all

: Resets all BGP connections.

external

: Resets EBGP sessions.

group

group-name

: Resets the connections with a BGP peer group identified by this name. The

group-

name

parameter is a string of 1 to 47 characters.

Examples

# Reset all BGP connections of VPN instance vpn1.

<Sysname> reset bgp vpn-instance vpn1 all

«
...
341
342
343
344
345
...
»

Summary of Contents for 5800













































































































































































































































































































































































































Reviews:

No comments