Home
/
HP
/
5800
/
Command Reference Manual

HP 5800, Command Reference Manual, Page: 273 / 396

Share

Page: 273 / 396

HP 5800 Command Reference Manual Download Page 273

264

pw-class

Description

Use the

pw-class

command to create a PW class template and enter PW class template view.

Use the

undo pw-class

command to delete an existing PW class template.

By default, no PW class template is created.

Syntax

pw-class

class-name

undo pw-class

class-name

View

System view

Default level

2: System level

Parameters

class-name

: Specifies the name of the PW class template, which is a case-insensitive string of 1 to 19

characters.

Examples

# Create PW class template

pw100

and enter its view.

<Sysname> system-view

[Sysname] pw-class pw100

[Sysname-pw-pw100]

pw-tunnel-policy

Description

Use the

pw-tunnel-policy

command to specify the tunneling policy for a PW class template.

Use the

undo pw-tunnel-policy

command to restore the default.

By default, only one tunnel is selected (no load balancing) in this order: LSP tunnel, CR-LSP tunnel.
If you specify a nonexistent tunneling policy by using the

pw-tunnel-policy

command, the default

tunneling policy is used. The default tunneling policy selects only one tunnel (no load balancing) in this

order: LSP tunnel, CR-LSP tunnel.
For how to configure a tunneling policy, see the chapter “MPLS L3VPN configuration.”
Related commands:

tunnel-policy

.

Syntax

pw-tunnel-policy

policy-name

undo pw-tunnel-policy

View

PW class template view

«
...
271
272
273
274
275
...
»

Summary of Contents for 5800













































































































































































































































































































































































































Reviews:

No comments