HP 5800 Command Reference Manual Download Page 271

Page: 271 / 396

262

no-control-word

: Disables the control word option.

NOTE:

The HP 5800 switch series do not support the control word option.

Examples

# Create a static VC between CEs connected to different PEs.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] mpls static-l2vc destination 1.1.1.1 transmit-vpn-label 111

receive-vpn-label 222 tunnel-policy pol1

mtu (MPLS L2VPN view)

Description

Use the

mtu

command to set the maximum transmission unit (MTU) for the Kompella connections.

Use the

undo mtu

command to restore the default.

HP does not recommend using the

mtu

command, because it affects only possible protocol parameter

negotiations and does not instruct traffic forwarding.

Syntax

mtu

mtu

undo mtu

View

MPLS L2VPN view

Default level

2: System level

Parameters

mtu-value

: Specifies the MTU for the L2VPN. It ranges from 128 to 1500 and defaults to 1500.

Examples

# Set the MTU for Kompella connections to 1000.

<Sysname> system-view

[Sysname] mpls l2vpn vpn1

[Sysname-mpls-l2vpn-vpn1] mtu 1000

ping lsp pw (for MPLS L2VPN)

Description

Use the

ping lsp pw

command to check the validity and reachability of a Martini VC.

Syntax

ping lsp

[

-a

source-ip

-c

count

-exp

exp-value

-h

ttl-value

-m

wait-time

-r

reply-mode

-s

packet-

size

-t

time-out

-v

]

ip-address

pw-id

pw-id

Summary of Contents for 5800













































































































































































































































































































































































































Search results

Summary of Contents for 5800

Reviews:

HP 5800, Command Reference Manual, Page: 271 / 396

Search results

Summary of Contents for 5800

Reviews: