manualshive.com logo in svg

HP 5800, Command Reference Manual, Page: 26 / 396

Share
Download
HP 5800 Command Reference Manual Download Page 26

 

17 

Field Description 

Threshold Value(%) 

Maximum ratio of the actual route number to the maximum route 
number in percentage. When the ratio is reached, the device 

rejects new routes.  

Interfaces 

Interface to which the VPN instance is bound. 

 

domain-id 

Description 

Use the 

domain-id

 command to configure an OSPF domain ID. 

Use the 

undo domain-id

 command to restore the default. 

By default, the OSPF domain ID is 0. 
With no parameter specified, the 

undo domain-id

 command deletes the primary domain ID. 

Usually, routes injected from PEs are advertised as External-LSAs. However, routes to different destinations 
in the same OSPF domain must be advertised as Type-3 LSAs. Therefore, using the same domain ID is 

required for an OSPF domain. 

Syntax 

domain-id

 

domain-id 

[ 

secondary

 ]

 

undo domain-id

 [ 

domain-id

 ]

 

View 

OSPF view 

Default level 

2: System level 

Parameters 

domain-id

: Specifies the OSPF domain ID, which can be in one of the following formats: 

•

 

Integer, ranging from 0 to 4,294,967,295. For example, 1.  

•

 

Dotted decimal notation. For example, 0.0.0.1. 

•

 

Dotted decimal notation:16-bit user-defined number, ranging from 0 to 65,535. For example, 
0.0.0.1:512. 

secondary

: Uses the domain ID as secondary. With this keyword not specified, the domain ID configured 

is primary. 

Examples 

# Configure the OSPF domain ID. 

<Sysname> system-view 

[Sysname] ospf 100 vpn-instance vpn1 

[Sysname-ospf-100] domain-id 234 

Summary of Contents for 5800













































































































































































































































































































































































































Reviews:

No comments