manualshive.com logo in svg

HP 5800, Command Reference Manual, Page: 221 / 396

Share
Download
HP 5800 Command Reference Manual Download Page 221

 

212 

Field Description 

LinkID 

ID of the PW in the VPLS instance 

VCState 

Status of the VC 

 

# Display the detailed information of VPLS connections of VPLS instance 

aaa

. 

<Sysname> display vpls connection vsi aaa verbose 

VSI Name: aaa                              Signaling: ldp 

  **Remote Vsi ID        : 500 

    VC State             : up 

    Encapsulation        : vlan 

    Group ID             : 0 

    MTU                  : 1500 

    Peer Ip Address      : 1.1.1.9 

    PW Type              : label 

    Local VC Label       : 1024 

    Remote VC Label      : 1024 

    Link ID              : 1 

    Tunnel Policy        : -- 

    Tunnel ID            : 0x3703ae 

Table 85

 

Command output 

Field Description 

VSI Name 

Name of the VPLS instance 

Signaling 

PW signaling protocol used by the VPLS instance 

Remote Vsi ID 

ID of the VPLS instance 

VC State 

Status of the virtual circuit 

Encapsulation 

Encapsulation type of the VPLS instance  

MTU 

Maximum transmission unit of the VPLS instance  

Peer Ip Address 

IP address of the peer of the VPLS instance  

PW Type 

PW type, which can be: 

•

 

label: NPW, the PW with a PE 

•

 

MEHVPLS: UPW, the PW with a UPE 

Link ID 

ID of the PW in the VPLS instance 

 

 

NOTE: 

You can use VCCV to verify the connectivity of a PW only if the two peers support at least one identical 
CC type and one identical CV type. 

 

display vsi 

Description 

Use the 

display

 

vsi

 command to display information about a specific VPLS instance or all VPLS instances. 

Related commands: 

vsi

. 

Summary of Contents for 5800













































































































































































































































































































































































































Reviews:

No comments